Brake Load Cell Issue/Polyphony Fix this please!

Discussion in 'Gran Turismo Sport' started by ZokyCRO, Oct 10, 2017.

  1. ZokyCRO

    ZokyCRO

    Messages:
    146
    Location:
    United Kingdom
    Hi all,

    Does anyone else have problems with thier load cell brake and auto calibration?

    I have a ricmotech load cell on t3pa pro pedals and it's simply not working corectly in the game as the brake auto calibrates every time I press it harder, so I find myself in situation that I am slamming the brake but can't get more than 50% power.

    Polyphony, software calibration is a must have for in game menus....please fix this as soon as possible.

    Has anyone come up with a solution perhaps? I don't want to remove my load cell because it works great in other sims, especially iRacing.
     
    VBR, danbojte, FPV MIC and 3 others like this.
  2. Grandi

    Grandi Premium

    Messages:
    263
    Location:
    Finland
    Have nothing as fancy as that but had to adjust the rubber brake mod on t3pa (thankfully the range was sufficient to not have to remove it altogether). Brake range setting would be much appreciated but I doubt this will happen. (Even on some PC titles (AMS) the only option has been to utilize DIview to reconfigure the range)

    Anyway, a thumbs up for the OP and the topic at hand!
     
    ZokyCRO likes this.
  3. GT_No1

    GT_No1

    Messages:
    23
    Location:
    United Kingdom
    Yes, I have the same setup, it took a while for me to notice, but I need to nearly put my foot through the floor to get it to 100%. Def something up. I was too busy looking at my erratic acceleration, i have to take my foot off and then back on to get 100%
     
  4. FPV MIC

    FPV MIC

    Messages:
    2,413
    I find my t3pa pro pedals (without load cell) do pretty much the same. They work fine after the initial calibration, but like yours they seem to keep auto calibrating with every slightly harder press until I can't press hard enough anymore (again like yours, to about 50% power).

    It could very well be a game problem more than a load cell issue.
     
    danbojte likes this.
  5. bokimoto

    bokimoto

    Messages:
    257
    Location:
    United States
    Not having any problems with Fanatec load cell brake, for what it's worth.
     
  6. ZokyCRO

    ZokyCRO

    Messages:
    146
    Location:
    United Kingdom
    Hmm it seems that putting abs to weak helps a lot so try that.

    Biggest problem is with gt3 cars,can't seem to get more than 50% strength on the brakes no matter what.
     
  7. danbojte

    danbojte

    Messages:
    3,372
    Location:
    Romania
    @ZokyCRO Same issue for me. Brake at 50% only despite of any ABS choice (OFF/Weak/Default). I hope (sure) it'll be fixed shortly. :tup:
     
    ZokyCRO likes this.
  8. ZokyCRO

    ZokyCRO

    Messages:
    146
    Location:
    United Kingdom
    ISSUE RESOLVED.

    Pluged in my wheel to pc and downloaded latest firmware from thrustmaster and it works perfectly now.

    I have done this recently though (5months ago) as I was buying a brand new pc so really didn't think this is needed,damn.
     
    danbojte likes this.
  9. danbojte

    danbojte

    Messages:
    3,372
    Location:
    Romania
    Thanks! :tup: I’ll do that tomorrow if there’s a new firmware. I did the last one in April I think...
     
  10. danbojte

    danbojte

    Messages:
    3,372
    Location:
    Romania
    That wasn't my case unfortunately as I already had the latest firmware (v25). I was forced, finally to remove the rubber add-on from my T3PA brake pedal, for having the whole 100% braking.