dice1998's 2022 Camaro 2SS + 1994 Subaru Dump

  • Thread starter dice1998
  • 80 comments
  • 21,668 views
One thing that would almost definitely turn me away from the car were I looking at one to buy, just for longevity concerns, is the fact the the windows drop an inch when you open the doors. Pull the handle, windows drop, open door. Except that's not the sequence you get. Pull the handle, open the door, window catches on the roof as the door opens because nobody waits that half-second after pulling on the handle to actually open the door. I don't know if that's a convertible-only thing because the top's different. Also, I can't get in and out without a severe rub on the seat's side bolster, which means there's gonna be a hole there in a few years.

But with the rental rate I had and getting this as a free upgrade, I'm not going to complain. Too much.

My Boxster does this exact thing. It drives me crazy. I'm conditioned to wait the half-a-second, but anyone who gets in my passenger seat obviously does not.

@dice1998 Can you elaborate on your plans? Am I sensing an overland build?
 
Last edited:
My Boxster does this exact thing. It drives me crazy. I'm conditioned to wait the half-a-second, but anyone who gets in my passenger seat obviously does not.

@dice1998 Can you elaborate on your plans? Am I sensing an overland build?

Gonna be honest: I don't know. The current plan is truck for a year or two and then flip back into something sporty such as a ZL1.

The more I drive this truck, though, the more I would like to tune it for a little more horsepower and torque but being it's a lease, it's probably not a good idea
 
Gonna be honest: I don't know. The current plan is truck for a year or two and then flip back into something sporty such as a ZL1.

The more I drive this truck, though, the more I would like to tune it for a little more horsepower and torque but being it's a lease, it's probably not a good idea

I didn't tune it. I did buy a pedal commander and it really helped me enjoy the truck more as I had a much much less delay in throttle response...


And then I traded the ZR2 in. 6 months later and 6,868 miles later.

For this:

20210601_200600.jpg




It may look familiar to some.
 
I finally had some time to take some decent pictures of the car:

20210714_181554.jpg
20210714_181654.jpg
20210714_181716.jpg
20210714_181741.jpg


20210714_181918.jpg


20210714_181801.jpg


20210714_182012.jpg



For those that do not know, the SS does come standard with:

Chevrolet's LS3 V8
Brembo Brakes front and rear
Blind Spot Monitoring
Rear Cross Traffic Alert
Lane Departure Warning
Front and Rear parking sensors
Forward Collision alert
Heads-up display
Heated and Cooled front seats
Power driver and passenger seat with power lumbar support
Memory driver seat and mirrors
Auto dimming rear view and side mirrors
Automatic Headlights
Automatic windshield wipers
Bose audio
Navigation system via Mylink (it's from 2015 so I do not rely on it)
Keyless entry and push button start
And a bunch of more stuff

My car was born with:

Magnetic Ride Suspension
Spare tire which is missing and has a tire inflator in it's stead
Sunroof

There are some things I have already changed to personalize the car to my tastes:

The first thing, and it's big to me, is removing the paonted-on pinstripe. Here's what it looked like with the pinstripe on:

20210614_082848.jpg


I really wasn't a fan of it at all. A local detail shop I really trust did the work and I'm super happy with it!

Next thing is changing the dial tip exhaust to a quad tip axleback:

20210714_182036.jpg



It sounds a lot "richer" without being annoyingly loud while driving.


I also bought some weathertech floormats for the car plus a weathertech sun visor.

The final thing I did, since the SS badge is missing in the rear, is add my own badge to the back.
20210714_182022.jpg



A lot of folks in my area of Florida have no idea what my car is and ask "what kind of Chevrolet Malibu is that?" or "Nice Impala!" (which for those across the pond are Chevys two best-known sedans in the US I think) so I decided to buy into that and badge my car appropriately.

"If there are people out there that upbadge their base model car, why can't I do the opposite" is the train of thought here. 😆


I do need to do some additional odds and ends to the car such as:

It has no front fender liners. They have been ordered and waiting installation.

The fog lights do not work which is also why I haven't installed the fender liners yet as I'd like to get it on a lift and mess with the fog lights before putting in the front fender liners.

My rear center arm rest has broken tabs so I've been calling it my Bluetooth armrest since I can take it out of my car and walk around with it if I wanted to.


20210714_182132.jpg


20210714_182105.jpg


Oh and if you wonder what the key for an SS looks like:

20210714_190822.jpg
 
Some things have happened since my last update.

I had to buy a new Key fob as the one I currently use is being torn up even though I don't touch it. It's a habit of these old keys. Because if that though, cut replacements are extremely cheap and you don't have to pay for programming as the car allows you to program a new key yourself!


I also had some spare time at work and had a lot of help working on getting the aftermarket fog lights to work.

20210904_100722.jpg


I was really happy that they were LED lights and I didn't have to worry about blowing a fuse.I will get the OEM ones working eventually. I'm curious on what happened with the previous owner and this project. It was 98% there. Mounted correctly and the grill cut quite well. Just not wired up for some odd reason..


Since that was done, the front wheel liners went in finally as well as a new rubber deflector under the front bumper.


20210904_103227.jpg



20210904_104530.jpg



That's when I learned that the front bumper isn't in the best of shape. Pictured below is the passenger front side. Note there's a large chunk of the bottom side bumper straight up missing.

20210904_104526.jpg


Screwing everything in will help keep things secure but I'll probably weigh out my options for a front bumper eventually.
 

Attachments

  • 20210904_092950.jpg
    20210904_092950.jpg
    78.1 KB · Views: 13
  • 20210904_093814.jpg
    20210904_093814.jpg
    58.4 KB · Views: 12
Two steps forward, one step back.

I finally have a complete, working fog light set!
20211006_184657.jpg


I found an aftermarket fog light assembly that is exactly the same as a GM part for a quarter of the price. I also replaced the light bulbs with LED lights purchased from Diode Dynamics to match the middle PIAA lights.

The one step back is when I accidentally destroyed some clips that hold the A pillar trim in place when I was trying to tuck in some cables from a dashboard camera and radar detector

20211005_121413.jpg
 
Last edited:
I'd like to start this post off with: I really liked the Chevy SS but that car wasn't taken care of. The SS also has a terrible infotainment system and no aftermarket options that worked for what I wanted (apple carplay and Android auto). Yes, there are one or two options but all of those options broke the heated/cooled seats settings and memory settings too.

The car also had some transmission issues from the first day I bought it. While the issue never became worse, no matter what I did, the issue never improved. I decided to sell the car and cut my losses between the money I spent sorting out the fog lights, wheel liners and other things. Also, the rear magride shocks started seeping..

Between the SS and my current car, I actually bought a 2019 Chevrolet Cruze Diesel and liked it a lot more than I thought!

20220223_125429.jpg


This car came with some pretty nice options too:
Gray Leather
Blind Spot Monitoring
Rear Cross Traffic Alert
Bose premium audio
Sunroof
Rear backup sensors
Apple carplay and Android auto
Heated (but not cooled) seats

20220223_125447.jpg


The car was torquey being the diesel and the 9 speed transmission allowed the car to always be in the powerband. Also for my heavy foot, getting 400 miles per tank with mostly city driving which allowed me to fill up only every two weeks for around $65 at the hight of fuel prices helped too!

I really would have like to keep this car but I cannot support 3 car payments (I also make car payments for my mom and dad's 2022 trailblazer that I bought them)

I yearned for a sports car again so I placed an order for a Wild Cherry Tintcoat Camaro LT1 until I realized how boujee I am so I changed my order for a Camaro 2SS for the leather, cooled seats, heads up display and more for a couple of thousand more. Then I was told that I couldn't get Wild Cherry any more for 2022 so I changed my order to Vivid Orange Metallic. I was under the assumption I couldn't get my 2022 due to supplier constraint so I ordered a 2023 2SS in Radiant Red. Then I discovered my 2022 order was picked up.

For this order, I only went with Dual Mode Exhaust. I did not want magnetic ride and I use Android auto so I didn't want navigation and I didn't want the Recaros Seats which is why I didn't choose the 1LE package. The only thing I wanted became discontinued (Chevy performance intake).

Skip to 6mos later and my Camaro finally showed up and I was happier seeing the color in person than from pictures. Yes, I ordered a color I never saw and I knew it was risky.

20220826_095500.jpg


I also wasn't sure at all about the silver wheels on this color but, again, seeing it in person helped a lot and this color/wheel combo is really growing on me.

I took it home the first moment I could on my dealer plate and encountered my first issue:

20220826_204527.jpg


That's how I had to drive to keep the car driving in a straight line. The next morning I took it to get fixed and it seems like the factory forgot to do an alignment while the car sat waiting for parts.

20220827_075850.jpg



No worries, one alignment later and I was happy.
After being cleaned up fully, I really am happy with the color:


20220903_142947.jpg

And I already have 231 miles on the car. I really am trying my best to correctly break this car in like my Green Camaro so I can confidently drive this car like I did the green car where applicable and legal.

This is also my first daily driver manual transmission car and I keep having to tell myself to do things like wiggle the gear stick, make sure it's not in gear when starting up and foot off the clutch and minor things like that.

I think I'll be okay. 😆
 
Last edited:
I actually got off my lazy butt since it was a nice day and took some half-decent pictures of the car:




*I tried to get the camera to capture the pearl effect/shine
.


I took a bunch of more pictures but am eventually going to take more because I overlooked some things such as the actual seats and engine bay.
Click here if you'd like to look through the pics and see the features a fully loaded early 2000's Lexus has.
I wish I had some actual hood pictures of my Lexus
 
@dice1998 $alute from Miami FLAWDUHHH! Congrats on making news post front page

As to jacking wiggly the stick.. man I see everyone do that but I'm the only one who does not, slot in gears ezpz. Keep it nice n hard!
 
Last edited:
received_1288305511897500.jpeg



received_726638025762302.jpeg



received_743718313941931.jpeg


I performed an Autocross. I won my class! It honestly surprised me as it was my first time running on this course with cones versus the last two times I did it where it was on a go kart course with defined corners.

I learned the car can perform but the tires (all season Goodyear run flats) are what is holding it back. I'm very impressed with myself and the car!



Still no good pictures.. yet.
 
Last edited:
Are you new to autocrossing, or been doing it a while? If you're going to autocross, you need a tire budget!!!

It's been years since I've been active, because I stupidly got married and bought a house! No spare change since then, especially after the divorce and getting her out of the house (financially.)

52748477348_e59cd0bbbd_c.jpg

I don't know what the rules are any more for tires in the stock classes, but back in the late 90s/early 2000s, several tire makers had special autocross tires, very soft, that were still DOT legal tires, and thus legal for stock classes. Hoosiers were practically racing slicks, with only two grooves around the tire and a sidewall wear rating of 0, but Yokohama and others made tires for us, too. The Hoosiers were worth at least three seconds on most courses, compared to what I drove on the street! I seem to recall looking at a rule book a couple of years ago and seeing that tires have been clamped down on in the rules, but even so, you want a set just for autocrossing if it's something you're going to be at regularly. You probably already saw the damage it does!

(BTW, the "Champion" status is not that big a deal. At the regional level, every class has a champion for the year, as long as you're there for a majority of the events, and there are at least three people in the class most of the time. I was also G Stock champion in Dixie Region, now with the "politically-correct" name of Red Hills Region, for 3 years, I think. I got coffee mugs for those! I never went to any higher levels of SCCA autocross other than a Divisional that we hosted, just to see. Did VERY poorly as I corded my fronts with a brake lock and was unable to run any further...)
 
Last edited:
Are you new to autocrossing, or been doing it a while? If you're going to autocross, you need a tire budget!!!

It's been years since I've been active, because I stupidly got married and bought a house! No spare change since then, especially after the divorce and getting her out of the house (financially.)

52748477348_e59cd0bbbd_c.jpg

I don't know what the rules are any more for tires in the stock classes, but back in the late 90s/early 2000s, several tire makers had special autocross tires, very soft, that were still DOT legal tires, and thus legal for stock classes. Hoosiers were practically racing slicks, with only two grooves around the tire and a sidewall wear rating of 0, but Yokohama and others made tires for us, too. The Hoosiers were worth at least three seconds on most courses, compared to what I drove on the street! I seem to recall looking at a rule book a couple of years ago and seeing that tires have been clamped down on in the rules, but even so, you want a set just for autocrossing if it's something you're going to be at regularly. You probably already saw the damage it does!

(BTW, the "Champion" status is not that big a deal. At the regional level, every class has a champion for the year, as long as you're there for a majority of the events, and there are at least three people in the class most of the time. I was also G Stock champion in Dixie Region, now with the "politically-correct" name of Red Hills Region, for 3 years, I think. I got coffee mugs for those! I never went to any higher levels of SCCA autocross other than a Divisional that we hosted, just to see. Did VERY poorly as I corded my fronts with a brake lock and was unable to run any further...)
I'm definitely still a newbie to autocrossing! Camaro 1LE's have Goodyear Eagle F1 tires and a wider track but I'm told 1LE's would be in a super stock class versus where I am (F-Stock).

That being said I'm not sure if my class changes by going to another, stickier set of tires 🤔. I was planning on getting some new tires once this set was up (obviously). I did really think about a set of autocross-specific tires but I don't think I'm going that route just yet.

The all-season run flats did pretty darn well all things considered. We only had 5 runs per group and the tires didn't really start overheating until the 5th lap and going by the on-board temp gage, they weren't overheating yet. It definitely tortured the tires... I think I'm going to torture the tires as much as I'm able to before it becomes dangerous and then go with a set of Continentals. I had those on my previous Camaro albeit 245mm square setup but it woke that LT1 up as compared to the all seasons that had.


Hmmm..
 
If nobody's said it, you'll probably want to run really high pressures while you run, like into the 40, 42 psi range. Keeps the tread from rolling the sidewalls onto the pavement. So take a 12-volt compressor with you.
 
Soooo it's been about 11,000 miles and almost a year since I took delivery of the 2SS. Still my daily driver and will be the forseeable future and still enjoying it!

It has had good amount of warranty work done. GM definitely are rushing these cars out without QC!



I did add another vehicle to the lineup for weekends though:

20230706_164007.jpg



20230706_164023.jpg



I'll be taking delivery of this some time this week 😁
 
20230815_155330.jpg


20230810_125303.jpg


I finally have taken delivery of the Sambar and boy did I have some highs and a flew lows.

20230809_135949.jpg


The truck is the complete opposite of my 2SS and it's awesome! As I found out, the Sambar is the only rear engined 4cyl kei truck. Very smooth power delivery and the cab is the quietest one of the bunch. Can it do 100kph with big ol' me in it? Eventually, yes.

20230810_215649.jpg


The radio has been the first modification I have done. In the above post, it has a radio but it's AM only and only for Japanese frequencies.

20230810_215625.jpg


I bought a decent, cheap radio with a big screen that has Android Auto and Bluetooth so I have some tunes to listen to while driving it. I also bought two new speakers as the one on the driver's side is original and brittle.

20230810_215713.jpg



Wiring it up was a challenge and I gave up and asked for reinforcements (my good friend) to help me out. I also converted the japanese battery to US spec to make replacing it easier in the future.. and to know it's a fresh battery.

20230812_193521.jpg


That night after getting everything to work, I was driving home only to have it overheat and evacuate a lot of its coolant on my driveway.





Problem solved though!




Camaro update: none. Still my daily driver, still love it!
 
Feel free to hit me up for any JDM parts (including maintenance). I have a plethora of websites that I can use to find part numbers, or equivalents, so happy to help.
 
Small Sambar Update/Addendum: What I thought (and signed up for) is a 1997 but I just found out it's a 1994. Does that change anything?

One thing: I'm closer to it having an Antique plate in Florida. :dopey:
 
This is going to be a LONG write up. Be warned.

Starting from the top, I bought the truck in July and took delivery in August and from August to October I had two major overheating issues plus a third even-more-major issue which I'll come to in a paragraph or two.

The first overheating experience, I was driving the truck home when I peeked down at the temperature gauge and noticed it spiked. Luckily I was 2 minutes from home and had green lights all the way to my driveway. The second I pulled in and shut the truck off, coolant spewed everywhere. Great.

Spoke to the guy where I bought the truck from and he said he'd cover whatever the problem was with the truck causing it to overheat. Awesome! Hagerty is really good on free towing locally so I had it towed to the mechanic that worked on the truck previously and let him work on it. Few days later good to go and I was told it was an old, crusty radiator cap that caused it. Cool no problem easy fix.

That should have been my first red flag in hindsight.

The second overheating problem happened 2 weeks later. This time I was 10 minutes away from home and in traffic so I pulled over to let it cool off. 30 mins later, one of my coworkers passed by and saw me and offered to drive behind me. I was lucky again and all green lights all the way home. Towed it back to the guy and told the guy I bought it from.

I visited the mechanic working on the truck this time so told me it was a stuck thermostat and he removed it and I "should be fine". This should have been my second red flag in hindsight.

Now comes the third one I mentioned. Unfortunately I cannot share the video as there's me swearing up and down in the video. To sum up this video, It's either a Cylinder loss or valve but the engine was knocking something ferocious this time every time it started up. I was 20 mins from home. Hagerty towed it all these times no charge to me.

By this time it was October, 2023. This time I had the truck towed home and garaged it. I knew I wasn't going to give up on the truck because every time I drove it, I had so much fun doing up to 60mph. I was over this mechanic and decided to have my dealership work on it this time. The original plan was to tow it to the dealership I work at and borrow a lift and work on it myself but alas, time was never my friend.

20240321_162949.jpg



I started doing homework and weighed out quite a few options from doing a diesel 4cyl swap to a Yamaha R1 swap. If it wasn't for the silly Hydraulic dump it had, I probably would have went one of these routes but I couldn't bring myself to do so yet thus I opted for a Subaru Remanufactured 4cyl that would be a drop-in.

20240321_160850.jpg


For giggles, I went over to our Subaru Parts dept to see if I could get anything for my Sambar but it's not recognized in the North American system. I found Yokohama Motors orders these engines on your behalf and that's what I opted for. The only things I had to carry over from my old engine is the accessory drive/belts and carburetor.

20240323_095535.jpg


This was a "wing it" process as things were dug into as no one here has ever messed with a Kei Truck let alone an inline 4cyl Subaru engine. It's why you'll see markings on some of the vacuum lines to ensure they go back to their correct spot. I ended up purchasing an very informative English service manual for it which came in handy for torque specs and wiring which I'll still need to use which I'll get into later on in this post. It's a good thing I had our guys work on this truck because I'm sure the previous mechanic wouldn't have told me things such as I should get a new fuel filter or new motor mounts. On the bright side, it did really have a new(er) clutch in it with a lot of life left! The remanufactured engine also came with all belts and even an oil filter! It essentially was "add fluids, carburetor, and accessory drive items and drop it back in!

20240323_095601.jpg


Did you know: The Sambar has the most cabin space of any of the Kei Trucks of this generation since the engine is ALLLLL the way in the back (it's rear-engined). It is also, to my knowledge, the only 4cyl Kei truck for this generation as the others are 3cyl.

20240323_173018.jpg


A lot of what you see above is transmission:lol:. I ended up buying a new fuel filter to ensure maximum life of the engine as well as put in diesel oil as a lot of guys in the south and warmer parts of the world run that since these engines are high revving engines. It's been 100 miles but so far so good!

20240330_152939.jpg


I also removed the giant Double-din-sized Single-DIN radio that was in it and add it a more "reasonable" Single-din screen/radio since it has wireless Android Auto and a remote to use the radio.

Currently I'm chasing some grounding issues as it has an issue starting until I play with the dump switch (heh). The longest part of this whole ordeal is ordering parts and waiting weeks-on-end.

Camaro update: 21k miles and I'm really not in love with this one as I was the green one. I'm looking into getting out of it into something different. Don't get me wrong, I love this Camaro but i'm not in love with this one like I was with the green one.

Not sure what I want to get..yet.
 
Back