Logitech G Pro Racing Wheel

  • Thread starter Thread starter timekiller001
  • 6,733 comments
  • 1,398,285 views
thanks - I'm sure I'll get used to it

one follow-up question - in mounting the sequential shifter I had to demount my h-pattern one and remount it. It was resting on the floor in between, probably on its side or something. Upon remounting it it didn't work (other than for 7th and reverse) until I recalibrated it - this was also the case when it was delivered new (none of the gears worked until calibration). Is this expected behaviour, or is it indicitive that something inside is loose in some way (I'd kinda assume that recalibration is almost never needed)
 
That's definitely unusual. Keep an eye on it, but it is the reason we provided the calibration function.
 
@LOGI_Rich - Hoping you can help with a very new issue.

After almost two years of flawless operation in GT7 my G-Pro wheel recently started acting up. Coincidentally, the issue started occurring immediately after the recent Spec IV update. It seems to occur most often at the new SUGO track but it has happened, albeit less frequent, on other tracks.

The issue is that the wheel will abruptly swerve either left or right then lock itself in that direction. The range of motion is very limited after it malfunctions. Very rarely, it will allow me to recenter and resume racing normally for a period of time. More often than not, it needs to be powered off then reconnected to the PS5 to resume racing.

Here are two videos of the aftermath.

The wheel has the most current firmware and I've disconnected/reconnected the power and USB cables but doesn't seem to help completely eliminate the issue. Any feedback on what might be going on would be greatly appreciated. Thank you.
 
Last edited:
Hi everyone,
After 360 hours with Sparco gloves… never experienced that with my old TM T300 RS Sparco Rally mod.
😢

IMG_4440.webp
IMG_4441.webp
IMG_4442.webp
 
Last edited:
LL1
@LOGI_Rich - Hoping you can help with a very new issue.

After almost two years of flawless operation in GT7 my G-Pro wheel recently started acting up. Coincidentally, the issue started occurring immediately after the recent Spec IV update. It seems to occur most often at the new SUGO track but it has happened, albeit less frequent, on other tracks.

The issue is that the wheel will abruptly swerve either left or right then lock itself in that direction. The range of motion is very limited after it malfunctions. Very rarely, it will allow me to recenter and resume racing normally for a period of time. More often than not, it needs to be powered off then reconnected to the PS5 to resume racing.

Here are two videos of the aftermath.

The wheel has the most current firmware and I've disconnected/reconnected the power and USB cables but doesn't seem to help completely eliminate the issue. Any feedback on what might be going on would be greatly appreciated. Thank you.
Hi there. Is it happening on other titles as well? Do please raise a ticket with support so it's logged, as your warranty is nearly up.
 
Hi there. Is it happening on other titles as well? Do please raise a ticket with support so it's logged, as your warranty is nearly up.
Hi, I don't play anything else other than GT7 so I couldn't answer definitively on whether other titles cause the same issue.

The good news is that I called Customer Care on 10/21 and a wheelbase replacement was quickly approved under warranty. After seeing the videos that were included in the original post, I guess they must have determined there is a hardware issue. They didn't explain the reasoning so that is speculation on my part.

The bad news is the replacement they shipped me was a RS50 wheelbase instead of a G-Pro so we'll have to determine next steps. The Logitech website is out of stock for G-Pro wheelbases. Hopefully there is stock set aside for warranty replacements.
 
@LOGI_Rich is there a way to remove those two hooks/L shaped parts. I guess these are to prevent the wheel base moving when using the table clamp. I have mounted the base on the Trophy seat with bolts. Every time I hit my knee on to those L shaped things 😄.
IMG_9130.webp
 
They're part of that entire sheet of steel that makes up the base, so the only way to remove them is to cut them off.
 
They're part of that entire sheet of steel that makes up the base, so the only way to remove them is to cut them off.
Thanks for your fast reply much appreciated! 🫶
 
This is the discussion thread for an article on GTPlanet:

Win a Logitech G RS50 Wheel and Pedals With GTPlanet’s Rig Builder​

The GTPlanet Rig Builder has been live for a little over two weeks, and now there’s an ever better reason to try it: we’ve teamed up with Logitech G to give one very lucky GTPlanet user a Logitech G RS50 System and set of RS Pedals!


Built this and processed my entries.

Not that it's likely but, if I were to win, I'd upgrade my wife's rig from the G29 currently installed to this kit.

Coincidentally, the entry period closes on my birthiversary. I call it that because, from my perspective, there is only one birthday. :lol: :mischievous:;)

@Jordan Thanks for having this drawing!
 
Here’s my competition entry build:
Great feature as I’d have no idea where to start with sim racing gear myself.
 
Back