Assetto Corsa PC Mods General DiscussionPC 

  • Thread starter Thread starter daan
  • 146,823 comments
  • 43,700,822 views
Jeroen V
Hi there,
Apart from the fact the jk1977 A4 STW looks way better, I feel (might be I should drive this one differently?) it is changing directions too aggresively. As if changing directions is not over the actual front wheels, but somewhere more to the middle of the car. Meaning; it changes directions on a different pivot point? Might be my personal feeling though, but noticable to me for some reason.
Click to expand...
I havent tried it yet, but it mught be because the toe is too agressive in the setting, try to get it near 0.0 front and back.
Negative front and positive rear will help the car rotate, but if its too agressive it'll be twitchy
 
LaChub
Hiding non-physical objects is not a problem, but with physical objects it doesn't work that way. You need to change .kn5.
Click to expand...
After hiding the meshes via [MODEL_REPLACEMENT_...] or [MESH_ADJUSTMENT_...] in extconfig.ini,
you have to edit surfaces.ini file for the invisible collidable wall meshes:

  • copy the surface [SURFACE_xx] with the ROAD surface.
  • paste it at the end
  • edit the number xx with the following one
  • edit "KEY=" with the mesh of the invisible collidable wall (NOTE: mesh only CAPITAL letters)

To find the invisible collidable wall meshes you have to:
  • unpack the track KN5 file (click on the .kn5 to highlight it and then hold shift while you double click the .kn5. This will automatically unpack it to a new folder)
  • open the track FBX with Blender
 
MasterFocus
I havent tried it yet, but it mught be because the toe is too agressive in the setting, try to get it near 0.0 front and back.
Negative front and positive rear will help the car rotate, but if its too agressive it'll be twitchy
Click to expand...
others parameters you have to check:
Caster: around 6/7 (easy to change in CMShowroom)
KPI: around 13 (idem)
Have fun, Mike
 
Quark67
After hiding the meshes via [MODEL_REPLACEMENT_...] or [MESH_ADJUSTMENT_...] in extconfig.ini,
you have to edit surfaces.ini file for the invisible collidable wall meshes:

  • copy the surface [SURFACE_xx] with the ROAD surface.
  • paste it at the end
  • edit the number xx with the following one
  • edit "KEY=" with the mesh of the invisible collidable wall (NOTE: mesh only CAPITAL letters)

To find the invisible collidable wall meshes you have to:
  • unpack the track KN5 file (click on the .kn5 to highlight it and then hold shift while you double click the .kn5. This will automatically unpack it to a new folder)
  • open the track FBX with Blender
Click to expand...
Very interesting, thank you!
And what values should be in surface.ini for an invisible collidable wall?

I just tried it, the car doesn't bump as much anymore, but the invisible obstacle is still there.

But this is progress for me anyway, thank you.
 
So I made a Prinz 4L 600 out of the NSU 1000 TT (for the upcoming Marlboro 12hr). As per specs, shortened it (not the full 14") (but didn't bother narrowing since the change was negligable). Seemed to go quite smoothly, until in-game, where the translation of the back wheels got lost. If it's anything like changing the track width in suspensions.ini, I can't find it. Anyone know where wheelbase is adjusted?

Blender-All-Good-02.png
- All good in Blender.

Showroom-All-Good.png
- All good in CM showroom.

InGame-Not-All-Good.png
Translation of back wheels is lost...

I tried "apply transformation" in Blender, but it wonked other things...
ApplyTranslationInBlender.png
ApplyTransformBad.PNG


- HELP :)
 
Last edited:
sab001
So I made a Prinz 4L 600 out of the NSU 1000 TT (for the upcoming Marlboro 12hr). As per specs, shortened it 14" (but didn't bother narrowing since the change was negligable). Seemed to go quite smoothly, until in-game, where the translation of the back wheels got lost. If it's anything like changing the track width in suspensions.ini, I can't find it. Anyone know where wheelbase is adjusted?

View attachment 1426672- All good in Blender.

View attachment 1426673- All good in CM showroom.

View attachment 1426674Translation of back wheels is lost...

I tried "apply transformation" in Blender, but it wonked other things...
View attachment 1426676- HELP :)
Click to expand...
1738779618454.png

maybe there is a problem here?
 
Hello guys I got a question... I got that F1 2002 mod but there is something bad about the tyres, they're supposed to be grooved tyres but the grooves look like they have been painted on the car and it seems like they are even slicks for a moment, is there a way to fix that model mistake for the SD 2002 cars.

I already thought taking tyres from 2001 or 2003 would work but after changing and saving the sets, the tyres looked the same.
Or is there an even easier way for this?
 
Last edited:
LaChub
Very interesting, thank you!
And what values should be in surface.ini for an invisible collidable wall?

I just tried it, the car doesn't bump as much anymore, but the invisible obstacle is still there.

But this is progress for me anyway, thank you.
Click to expand...
Perhaps there is another invisible collidable wall meshes. Which is the track you are modding?
 
Hi gents,
About the STC Audi A4 here is what i do after downloaded her at ACTK (dont know if its the last version)
In CMshowroom adjust these settings:
caster: 6.6~
KPI: 13.xx~ (was at 0, not good)

in car.ini: test those values, they are good enough imo
[CONTROLS]
FFMULT=1.614
STEER_ASSIST=1.000
STEER_LOCK=480
STEER_RATIO=16
LINEAR_STEER_ROD_RATIO=0.0033

In Game, adjust front TOE to -10~ and rear TOE to +10~, drive like a charm except the gear ratio too close in 2/3/4
for the gearbox, have a look there:
drivesport.myshopify.com

Audi 01E 6 Speed Dog Kits

Upgrade your Audi 01E gearbox with a 6 speed kit suited for circuit and rally racing. A variety of gear ratios are available to better suit your needs. This kit utilizes the OEM final drive. The installation of this kit requires modification to the transmission and the input shaft is a 26 spline...
drivesport.myshopify.com

PS: this car have also a problem with the 'rod_length' parameter (both front and rear) which also conditions the TOE and camber parameters
 
Last edited:
Quark67
Perhaps there is another invisible collidable wall meshes. Which is the track you are modding?
Click to expand...

Malaysia

Based on the original Malaysia for rFactor by Cico76 Credits Original creators: *cico76/Kicker/Alain Fry * - modeling, texturing, scene Kicker/Alain Fry - former modeling, organisation Kicker/Alain Fry - textures
www.overtake.gg www.overtake.gg

I want hide 1WALL7_3_SUB1
 
Last edited:
Mike173
Hi gents,
About the STC Audi A4 here is what i do after downloaded her at ACTK (dont know if its the last version)
In CMshowroom adjust these settings:
caster: 6.6~
KPI: 13.xx~ (was at 0, not good)

in car.ini: test those values, they are good enough imo
[CONTROLS]
FFMULT=1.614
STEER_ASSIST=1.000
STEER_LOCK=480
STEER_RATIO=16
LINEAR_STEER_ROD_RATIO=0.0033

In Game, adjust front TOE to -10~ and rear TOE to +10~, drive like a charm except the gear ratio too close in 2/3/4
for the gearbox, have a look there:
drivesport.myshopify.com

Audi 01E 6 Speed Dog Kits

Upgrade your Audi 01E gearbox with a 6 speed kit suited for circuit and rally racing. A variety of gear ratios are available to better suit your needs. This kit utilizes the OEM final drive. The installation of this kit requires modification to the transmission and the input shaft is a 26 spline...
drivesport.myshopify.com

PS: this car have also a problem with the 'rod_length' parameter (both front and rear) which also conditions the TOE and camber parameters
Click to expand...
Please can you let me know how to make the caster and KPI adjustable? My CM is 0.2.6
KPI caster.png
 
Mike173
So rather than trying to help, you can just throw it in the trash.☹️
Click to expand...
Yeah, seems like people are getting annoyed and impatient because a few of us are trying to make a really nice car even better. Not sure what to call that, but it's a really baffling attitude to have in a modding thread.
I guess in these attention-deficit days some people just want a steady stream of mediocre stuff that they'll drive once before moving onto the next one. Quantity, not quality.
 
marc magnela
ACTK must not have seen your message because he has just published a new version announced on his telegram. :crazy:
Click to expand...
:lol:Sometimes when I follow mod updates, many things surprise me.For example, these👉
Скриншот 06-02-2025 121729.jpg

it's obvious, isn't it, or am I wrong?I have been observing these "protrusions" of the insides since the very first release.I see the same thing with the extension file.👉
Скриншот 06-02-2025 122908.jpg
Скриншот 06-02-2025 122950.jpg
it seems that those who do this don't really understand it:lol:
 
Sharing a mod? Host it on GTPlanet Downloads. Free, public hosting for files up to 10GB in size.

Similar threads

Famine
Assetto Corsa EVO Early Access Discussion Thread
23 24 25
Replies
721
Views
138K
Beezer215
Beezer215
S
Logitech G Pro wheel settings Assetto Corsa
Replies
0
Views
3K
Shah1
S
OH1955
  • Question Question
Anybody got Oakes Field (Nassau) for Assetto Corsa?
Replies
5
Views
8K
OH1955
OH1955
Famine
Assetto Corsa Competizione Ultimate Edition Now Available on Steam
Replies
8
Views
8K
Apocalypse211
Apocalypse211
GTPNewsWire
Assetto Corsa Modder Creates Real Road Circuit Using Photogrammetry
Replies
16
Views
17K
Perico Lospa
Perico Lospa

Latest Posts

Back